J.B.D.S. Power

The HFP CP range of conventional panels offers the same reliability, durability and flexibility already afforded by the HFP FIREline range of analogue control panels. 100% compatible with the complete Hochiki conventional range of products the HFP CP panels offer the installer complete flexibility and total peace of mind. Also available are a 4 zone (HFP CP-4), an 8 zone (HFP CP-8) and a range of Active Repeater panels (the HFP CP-R range).

• T-shaped output
• Connector type connection method

• Increases 100 mW (4.0 mA) for High Speed mode
• One or two more units connected: -20 to +55 °C; 3 to 10 more units connected: -20 to +50 °C; 11 to 16 more units connected: -20 to +45 °C. When using 2-outputs, one unit is counted as two units. All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.

• Wire cross-section 0.34 mm2
• Rated voltage range ≤ 250 VAC/VDC
• Temperature range -30...80 °C
• Enclosure rating (IP) IP 68

Hochiki HFP AS/S Download Lead (Economy) (HFP APS-DLL(ECON))

HFP AS/S Download Lead (Economy) is an economical programming cable, for direct programming of HFP-APS control panels from PC, serial port connection, weight 200g

• Low profile
• Rugged design
• Dedicated cable screen terminal
• Accepts from 1 to 2.5 mm² cables
• Quick connection via square cable clamps

We are engaged in offering Autonics CR30-15DP PNP Cylindrical Capacitive Proximity Sensors to our clients. Our range of products is appreciated by our clients. 

• Flexible alignment possibilities

• For 50 × 50 × 20...30 mm

• Simple installation

• Stainless steel

• The mounting system allows to adjust sensors and reflectors and to turn them around 360 degrees in horizontal and vertical direction.

• Material Mounting Head : Stainless Steel V2A

• Material Mounting Plate : Stainless Steel V2A

• for Round Profile Diameter : 8...12,5 mm

• Packaging unit : 1 Piece

We are engaged in offering Balluff BTL5-A11-M0150-P-S32 Photoelectric Sensors to our clients. Our range of products is appreciated by our clients. 

• High-flex fibers and 90° cable exit for cable breakage prevention
• Models with hexagonal back for simplified one-nut mounting
• Sizes M3 to M6

• Only the FS-T1 and FS-M1 can provide stability outputs.
• If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less.

• When extended, the ambient usage temperature varies according to the following conditions. Be sure to mount units on a DIN rail (attached to a metal plate) and ensure that the output current is 20 mA or less. When extended

• Standard model - Cylindrical housing M12
• Housing length 50 mm (cable) / 60 mm (connector), cylindrical M12, nickelplated brass
• Short version, housing length 35 mm (cable) / 45 mm (connector)
• Supply voltage 10 ... 30 VDC, output current 200 mA
• LED, protections against short-circuits, induced overvoltages and power supply reversal built-in
• PNP and NPN, N.O. and N.C. executions

• EXTENDED RANGE INDUCTIVE SENSORS
• EXT RANGE 600 DC 2 WIRE M12
• 12 MM THREADED

Omron Industrial Automation E3Z Photoelectric General-Purpose Sensors offer industry-leading performance in a compact (31mm height x 10.8mm width x 20mm depth) plastic housing. Omron E3Z Photoelectric Sensors feature a high-power LED that allows optimum detection over long distances (up to 30m) or in dirty or dusty environments. The series provides high noise immunity against interference from inverters and other inductive loads. All E3Z plastic models are rated IP67 and tested to withstand 1200psi washdown applications.

Typical installations are, assembly robots, cream solder print machines and PCB assembly machines.